Did you know that the majority of Heat Loss in winter
and Heat Gain in summer occurs through your ceiling / roof ? 
50% - 75% up heat flow in winter
and up to
93% down heat flow in summer

SO CHOOSING THE RIGHT RADIANT BARRIER IS IMPORTANT !

Despite the fact that they have been proven to be one of the most effective
forms of insulation, the old adage,
 you get what you pay for applies to radiant barriers.

  Because of the popularity of radiant barriers, many builders, architects, insulation contractors and 
  homeowners are turning to the product for residential insulation. But not all radiant barriers are alike. While
  some radiant barriers may seem to offer the same benefits at a cheap price, is sometimes just what it
  sounds like, thin lower quality radiant barriers are not always your best value.

  This is particularly true of deck-applied radiant barrier, the lowest-rated radiant barriers on the market
  today. Manufactured with easily damaged materials and applied with glue, deck-applied radiant barriers
  cannot be factory-repaired; so on-the-job repairs will always show. The wood that includes foil on the
  underside and must be thrown away is wasted material. Unnecessary costs include wood that cannot be
  flipped on hip roofs. This and the fall-down can account for as much as 20% waste. What's more, you are
  restricted to a specific type of wood with deck-applied radiant barriers.

  In contrast, radiant barrier rafter application offers a SUBSTANTIAL INCREASE IN PERFORMANCE
  as compared to standard deck-applied radiant barrier applications. Whereas standard deck-applied radiant
  barriers offer one layer of protection with one airspace, under rafter installed radiant barrier has two layers
  of protection with airspaces to enhance protection. And each of the two reflective surfaces of the radiant
  barrier reduces radiant heat transfer up to 95%.      

Under Roof Rafter installation Most Effective -Best Installation Method * TWO LAYERS of protection with air spaces to enhance performance * MINIMUM 17 % IMPROVEMENT in performance over standard deck applied radiant barrier applications

Not as Effective * Only one layer of protection * No additional air spaces * Pure conduction of heat occurs where Radiant Barrier is sandwiched between trust and roof deck * Trusses re-radiate heat down, reducing overall performance

 Radiant Barrier also qualifies for Florida Energy Code and California Title 24 Energy Code Credits, and its 
 Energy Star Partner Rating helps homeowners qualify for energy-efficient mortgages.

Because they are, and YOU GET WHAT YOU PAY FOR !

The RIGHT Attic Radiant Barrier is the real cost-effective solution, one
that provides 100 % customer satisfaction, energy-efficiency and builder profitability all at the same time.

DID YOU KNOW that an ATTIC RADIANT BARRIER SYSTEM
 is far more ENERGY EFFICIENT
and Cost Efficient than a spray foam system ?

 Builders, architects, insulation contractors and homeowners have a variety of choices when it comes to 
 residential insulation. While some of those choices may, on the surface, seem to offer the same benefits,
 when one looks deeper, the true value becomes clear.

 Many builders have turned to low-density spray foam insulation systems because of a perceived difference in
 cost and profit margin. The truth is that radiant barriers significantly improves the quality of a home and,
 with a standard mark-up, is far more profitable.

 Under Federal code and many if not most states Building Code, spray foam insulation in attics where access
 is available is required to be either covered with drywall or be covered by a thermal barrier.

 Not so with our ATTIC " NT " radiant barriers. Most of the codes also requires a 1-perm or less vapor
 barrier / retarder over the foam to the exterior of the roof deck for asphalt shingles.The vapor barrier /
 retarder will get punctured when the shingles are installed. With Attic Radiant Barrier, that problem is
 obviated by the fact that field and inside support personnel, along with insulation contractors, are readily
 available to service your needs on a local level. With foam insulation, you must rely on licensed dealers and
 distributors to service your needs.

 As for the cost issue, Attic Radiant Barrier plus R-30 Fiberglass Batt Insulation equals about $1.25 per
 square foot when installed; while low-density .05 lb. spray foam insulation runs approximately $2.00-$2.50
 for R-19 value. Even if the installed cost were the same, the customer gets better performance with the
 Radiant Barrier --- that makes it a better value. What’s more, homes will achieve 12% for vented attic
 Radiant Barrier system versus standard R-19 insulation. And peak demand reductions are 16% -- 3x more
 effective than adding more insulation. With spray foam, energy savings is only 9% compared to standard
 R-19 insulation on ceilings as tested by the Florida Solar Energy Center Flexible Roofing Facility in 2000,
 with a peak demand reduction of just 5%.

 As a result, homeowners will enjoy a far better return on investment with Attic
 Radiant Barrier plus R-30 fiberglass batt insulation versus spray foam with 
 standard R-19 insulation.

 For saving energy and improving comfort, Attic Radiant Barrier is the preferred 
 option for increasing energy-efficiency, reducing utility bills and improving
 overall comfort in residential construction today.

BTUBUSTERS ^tm Attic NT Radiant Barrier " The RIGHT Radiant Barrier"

Q - How do I determine the best place to install BTUBUSTERS Radiant Barrier ?

  If you live in climate area #3, then installation as in pic # 3 is recommended. Insulating any 

  Attic Mounted HVAC Duct Work is HIGHLY RECOMMENDED.

Available in 500 sq. ft. rolls.

Additional Info and Pics on Attic Radiant Barrier

is recommended for all applications as shown below.

  In new construction and re-roofing an existing home where the plywood roof decking is being replaced,
there is an alternative, which offers the advantages of location 2 while providing the construction ease
 of location 1. This technique places the radiant barrier on top of the roof rafters (or trusses) before the
roof decking is applied. It is installed so that it droops 1 1/2 to 2 inches below the upper surface of the

When the roof decking is applied, an  airspace separates it from the radiant barrier in a way similar to
     that of location 2. This airspace also can be vented separately from the attic.  As with location 2 the most
   reflective radiant barrier surface should face downward toward the attic airspace. 

  NOTE: Our BTUBUSTERS ^tm Radiant Barrier is PERFORATED and has
TWO IDENTICAL FOIL SIDES, therefore you get both upward and downward heat rejection
 for better Summer and Winter ENERGY $AVING$.

 BTUBUSTERS ^tm Radiant Barrier

Stops 95% of Radiant Heat.

Additional Product Specifications

Concrete Slab Insulation #1

Concrete Slab Insulation #2

MULTI LAYER RADIANT BARRIERS  & INSULATION